BRIGHT + FLASH = NEW SPECCY (C) 1997 Evil-Genius
________________________________ There were times
kogdarozhdalsya Spectrum, colored graph-ka, computers of the
time assumed to talos large slope, and tembolee 16 colors. Some
dazheschitali is overkill as well as the 48Kb memory - say,
est16Kb, and that's enough. NoKlayv Sinclair looked at
buduscheei made a 16-color graphics. However, there was still a
bit that he has mobilized kakmertsanie (Flash), that are
time-Names was unheard of and ochenkruto! But this thing is not
nashlashirokogo dissemination users SPECCY. Our time
dictates its new, higher demands: more colors and
permits, so has already been done
a great variety of graphic
lotions, but they all have two
major shortcomings: 1 - they do not
compatible with the previous screen
they are not common; 2 - be
to sit with a soldering iron to
connect this gadgets and more
long to find the software for this extension.
The idea to connect instead FLASH'a
increased brightness of the background color
(PAPER), and the old BRIGHT leave the management of high
brightness color point (INK) flew in the minds of spektrumistov
a long time, and I do not claim to its authorship. However, I
believe that even it is time to implement it! Why? - You ask.
Because it is devoid of the above
deficiencies. Remains fully compatible with standard screen,
under this pribambas already written a lot of editors. Do not
to sit with a soldering iron - just resolder only one (A)
posting, and this can be done through the toggle switch ON /
OFF!
But what about the 48 BASIC? - Ask
you have a question to me. It is very simple -
the cursor will now be allocated not
shimmer, and high brightness
background, as in 128 BASICe, the more you can always put
pressure on the lever composter ON / OFF!
In connection with this appeal to all
Authors demuh, programs, etc.
support this proposal,
the more so because it allows
increase the range of colors in
twice! Without increasing
Neither the volume nor the complexity
programs. To eat, whereas before
you can install on a blue background with a white point, only
two combinations: white with a blue dot background and a white
bright spot on a blue bright background, you can now install
four (4) modes: the white dot on a blue background; white
bright spot on a blue background; white dot on a blue bright
background; white bright spot on a blue bright
background! Now, the number of combinations
twice. And not to talk
wasted language, I have installed on your
PROFI a lotion, through the switch. It turned out that to
connect it is not easy, but very simple, so here we present
circuit hemmed this stuff to different components:
1. Stored tumbler type PC2
or any other with a pair of switches, a soldering iron and
wire. It is not recommended to drink beer and others before
connecting!
2. Find resistance from 1 to
3 rooms, fluster, check and
Only now you can with a clear conscience blowing beer!
PENTAGON 48/128/256/512 and
etc. Find the IC D47 KP2 (or
KP12), she connected on 10 and 11
feet. Disconnected, and disconnect them 11 feet from the signal
(10 foot is still connected to the signal). We call a 10 foot
Bright ink and, 11 feet - Bright paper. Signal, which came on
10 and 11 feet - Bright. Now we find the signal at 12 feet
FLASH D7 La3, cut it from 12 feet and serve
improvements to the scheme. A 12 foot
la3 obzovem as upr.Flash. Now connect all the signals
scheme (Fig. 1) so that the top
switch was open when the revision is included and the lower
switch was closed by the circuit FLASH - Bright paper, which
included completion. (By the tumbler means one triple contacts
button-type PC2).
Figure 1
Bright ink
BRIGHT /
| Bright paper
FLASH /
upr.Flash
R1 = 1K-3K R1
Flash signal can also find a 19 foot D40, then 19
D40-foot IR23 is FLASH, cut off from her signal - this panel.
Flash.
LENINGRAD2 16/48/128/256 and
etc. Connects the same way as
PENTAGON, but the signals are taken
respectively: Bright ink at 13
leg D34 KP16 (14), ibid
Bright paper with 14 feet D34;
Bright - the signal that
came on 13 and 14 feet; FLASH -
signal coming at a pace D12 la3
itself is a foot panel. Flash.
PROFI 128/256/512/1024 etc.
Felled the same as that
PENTAGONa, but the signals are taken
respectively: Bright ink at 10
leg D61 KP12 (2), ibid Bright
paper - 11 foot D61; Bright -
the signal that comes to
10 and 11 feet; FLASH - a 19 foot
D59 IR23, track, running at 19
leg D59 - Ex. Flash. Attention
some versions have PROFI
there is resistance, so
second copy to put there
necessary.
SEPARATION OF BRIGHTNESS.
If you're tired of some
programs that have ever turned Brigh not where it should, then
of this deficiency is very easy
get rid of: it takes only 2 toggle switches and a hot (no, not
coffee:) soldering iron, with which is going to the second
scheme (Fig. 2) cmysl which is what we get
Bright on the ability to disable
ink and paper separately.
This scheme does not conflict with
the previous one and makes no
distortions in the computer.
What to do: find signals Bright Ink and Bright paper
(Read about their presence in
previous scheme, they are identical)
Now skip all of the signals through the switch to the scheme:
Figure 2
Bright ink Br.ink
GND Br.pap.
Bright paper
If there is something you do not understand, then:
1. Reread the article.
2. Call me.
But not vice versa! .. BYE!
EVIL-GENIUS FROM UNICUM
X-PROJECT ASSOCIATION
CALL ME: (0572) 720756
________________________________
