ZX-WinWord V3.0 Modul v1.03
(C) Shaitan / Stars of Keladan
Presenting your attention the description
File additions to our editor
ZXWinWord v3.0 (with other versions of the editor data
supplement does not work will). Firstly, I want to say about
that I was led to this innovation. To add kakuyunibud function
in the editor should be have a free chunk of memory, which
today no longer exists. It's no joke
process 48Kb and 32Kb of text sprites. After long walks in the
source code, free memory was found, but very it is not enough,
and the editor wanted to make it accessible to everyone (not
all yet memory in wheelbarrows more than 128Kb).
It was therefore decided to make an overlay
structure.
To load the
you need to select the function from the main menu
click Overlay. This will be followed scans the current drive
for a file on him Additions w.wor3_0.add. If such a file on disk
No then you will be breaking off, otherwise it will be an
analysis, then you will be asked to choose one of the available
overlays. After loading is directly overlay will take you to
the main menu where you can already work as well as before. To
to run the downloaded overlay
editing mode, you must have to be in command mode (press EXTEND)
and start the overlay key V. After
then act according to the description of the overlay.
Description overlays
In this version of the file has Additions
Xia three overlay. On each order.
GFX Printing Text v1.0
This overlay is used for printing the document together with
the sprites, the which have all long been dreaming of.
Immediately after it is loaded into memory you need to also
load the printer driver. In the author's delivery driver
attached printer connected through the ZX-Lprint
III. You navenoe think what to write
driver is the destiny of only the elect. I
you for this answer, that the driver napisat
not easy, but very simply, is used for long-established
standrat on driver. Thus, the driver allocated
256 bytes, located at
# 5B00-# 5BFF (23296-23551). Overlay works with the driver as
follows. Before you print to initialize the device (makes the
call procedures at # 5B02 [23298]). For
output bytes to the printer called the procedure located at #
5B00 [23296]. Both of these procedures are called
every time you print the text. The main feature is that if you
otslezhivate pressing BREAK, then
necessary when it is pressed, reset
Flag C.
And now on with the overlay. After
thereof, you will see the start menus, with
following paragraphs.
F.page - page selection, which is to be printed.
E.page - choose the page on which
inclusive, will be used for printing.
Density - choose print density.
Re-install - pereinstalyatsiya overlay.
Simply put download a new driver
printer.
Start - run directly overlay.
The printing process uses the following ESC-sequence.
# 1B # 4A # 18 moving the paper forward
24 * 0.118 mm
# 1B # 2A N misuse of print
graphical mode. N - number density
from 0 to 6.
# 0D-back to the printer head to the starting position.
Text Convertor v1.0
As you probably guessed from the title, this overlay is
designed to converting text from
memory in a format suitable for use in
editor.
Menus of the overlay has a
The following paragraphs.
Search code - in this menu you
can specify the character code, which you would
would replace (in the decimal system
radix)
Replace code - well, and then you enter the code
character, which you need to replace the found character
sIngle convert - start conversion
on the above parameters.
Med conver - start conversion
Text from the Format Editor Kowalewski
MicroEditor the normal encoding
Tablic convert - start conversion
Text on a pre-loaded table.
If the table has not yet been loaded, then
will be done loading the table.
Load tablic - Loading Table
conversion. This table should
be up to 256 bytes and have a very
simple format, ie in place of the symbol
(Starting from zero), which should
replaced, should stationed character code, which must produce
replacement. In the author's delivery prilagayutsya four
tables: DK-7BIT, ISOLAT-1 KOI8-R, WIN866.
Extend Code Killer V1.0
Well, this overlay is designed to
delete any characters from the text, as well as control
characters ZXWinWord. Just want to make a reservation, the
algorithm remove the very symbol of the brake, but very short,
which put in these conditions in the first place. For
example, say that the removal of control characters in the
description editor it took 5 minutes 25 seconds. A
Now about the menu.
Erase code - enter a code symbol to be removed (in the decimal
system radix)
Single killer - run delete text you entered the code symbol
eXtend killer - start remote control codes ZX-WinWord.
For all questions about the editor and the file
addition, you can contact me
at the following addresses.
Fidomail: 2:5057 / 21.36 To: Max Shashkin
Subj: ZX-WinWord
Snailmail: 443110, Russia, Samara,
st. Chelyuskinites 19 kv.40 Shashkin Maxim
Or telephone (84-62) 34-82-92
ask Maxima
2000 (L) Copyleft, "STARS OF KELADAN"
