(C) MicroArt
(C) 1995 MaxSoft (?)
Personal computer ATM-TURBO 1
PCB version 4.10-4.50
Hardware error fee.
On-board ATM-TURBO 1 is used
very uncomfortable addressing additional
port configuration.
Error 1 - Switching Display Modes
combined with the port # FE. Which leads to
A broken-protected
ANTON PROTECTION SYSTEM, DIMAN
PROTECTION SYSTEM! And so the same of others, where
Team OUT (# FE), A duplicate command
OUT (# 3E), A This leads to a change in video mode and memory
addressing (a sign is erratic color picture
in high resolution mode).
For example do not work: LYRA-2 / 9 (disk
version by Vasilyev Anton) SONG'LN5
(Disk version by Softstar) ......
Error 2 - use for decoding
Port # 7FFD and ports Music coprocessor addresses A9. In recent
years, Addressing port # 7FFD programmers use the command OUT
(# FD), A 7 bit thrown down with the battery! But for ATMTURBO
requires a "1" on the A9. Because of this, do not go to the
following program: STS debuger-monitor, SHOCK MEGADEMO, INSULT
MEGADEMO, toy RONDLAND, ASM v1.03 and above, FARLIGHT-2 and
many others Toys and programs, disk
loaders, written in the CIS.
Mistake 3 - VG93 chip does not work
in turbo mode!
Method of refinement described in the documentation MicroART
(at 1 ms. 555kp12) helps in the treatment of 1-th problem, but
does not solve the 2-nd (especially the third), so the same
will not work such a wonderful program as Honey Comander (lost
function RESIDENT, RAM-DISK 512k), a turbo button
only works in CP / M. Below is a my [(c) MaxSoft] own way
address all three issues, which in HC
all functions + get an almost
100% Pentagonsovmestimuyu machine (except
Interrupt and multicolor).
To do this:
1) carefully unsolder and bend ms following conclusions: 1.D17,
3.D69 2) bite of chip D50 conclusions
2, 3, 4, 5, 6, 7 (in most case).
3) take on a new ms. 555TM9 bite findings 10, 11, 12, 13, 14,
15 and soldered to D50 so that, to pins 2, 3, 4, 5, 6, 7
fall into the corresponding holes on the
D50, pins 1, 8, 16 were closed with
relevant conclusions of D50 (and the pin 9
until the bend).
4) Collect scheme
555TM2
+5 V 5 January LOCKP
RES x R tt Q
2
RG0 D
2kom 3
C
June 4
+5 V x S Qx
LOCK button
gnd
68nf
X
1
A9 March 1
2 to 1 pin. D17
LOCKP LL1
cut
X
4
/ PRRD June 1
5 to 3 pin. D69
LOCKP LL1
9
/ BRDWR January 8 to 9 pin.
10 soldered
LOCKP LL1 top
D50TM9
And now briefly about how it works. When my computer starts
the trigger reset signal RESET, the signal
LOCKP = 0 and access to all ports enabled.
If we work in the CP / M - Pressing
lead to nowhere, because RG0 = 0. In
SPECTRUM situation is different RG0 = 1 and press
button leads to a latch in RG0
trigger and now LOCKP = 1, access to all
port CP / M is prohibited.
And so you run the program (eg
of HC) and the program hangs! Press
Reset (to return to the Honey Comander)
and run the program again. But now,
Once the program starts to load
(It is necessary that-be had set HC
its resident part), click on
click LOCK. The program will work. (If
you do not use the HC, after-
SPECTRUM simply click the LOCK).
LOCK button is not fixed - just a time to press her
on-Spectrum and until the next RESET any program that will
identify it as PENTAGON 128.
And now for the finalization for VG93 in
Turbo mode.
There is nothing new invented
(Scheme simply taken from TURBO2 +), using 1 ms. (555la3) and
the remainder of the previous revision element ll1.
Necessary to cut the track leading from
3 pins D75.
cut
X
October 13
D75.3 '& 11' & 8
12 o 9 o to 24 pin. D1
LA3 LA3
1 April 1912
D89.3 '& 3' & 6 January 1911
VGCS 2 o 5 o 13
LA3 LA3 220pf TRB LL1
D61.4
3kom
Personal computer TURBO 2 +
PCB version 7.00-7.10
Hardware error fee.
The basic error - use when decoding the port # 7FFD addresses
and ports muz.protsessora A9. Because of this, do not go
following program: STS debugermonitor, SHOCK MEGADEMO, toy
RONDLAND, ASM v1.03, FARLIGHT-2 ... many other toys and
programs, disk loaders written in the CIS.
Recently, to address the port
# 7FFD programmers use the command
OUT (# FD), A thrown down from the 7 th bit
battery. On a standard TURBO-2 +
for decryption also takes into account the discharge
A9.
To treat this problem, take
555LL1, bend her legs all except 7
and 14 and 14 are soldered to any fade
chip (so that were welded
only supply connections), then gently
unsolder the pin 1 of decoder and DD17
include the following scheme:
cut
X
1
A9 March 1
2 to 1 pin. DD17
RD (vyv. z80) LL1
Now, A9 will participate in deciphering the ports only when
the active signal RD (read ports ADRD, TLRD). As for reading
the block ports # xxFD (Muz.protsessora) is always used
complete addressing, we obtain a complete
compatibility with the Pentagon's ports!
The problem of PC-XT keyboard.
Some processors 8031 is very unstable work with external
synchronization. Therefore, if you are experiencing frequent
crashes when working with IBM-PC keyboard (sticky keys in
SPECTRUM), Make the following revisions. Cut
conclusions of 18 and 19, 8031, and solder to them
Quartz 12.8 MHz (pick experimentally) and solder the 2
capacitors land (10-20 pF) on the conclusions of 18 and 19.
Connecting the HDD to the motherboards Turbo 2 +.
So you've decided to buy a hard drive
for your computer. First of all, think - but is it really you
need it? Because it can be used only in professional running CP
/ M (MicroARTa dream about fabulous ability to download programs
SPECTRUMa for the HDD appear
will remain a dream). Although the current prices on the IDE
20-40mb it can buy anyone. Okay. Let's start from the
beginning. Take your HDD and connect it to the board a train
(not mix 1 and 40 contacts). Start
program FDISK (sold in
MicroARTe) and make sure that the settings on your HDD are
determined by the program. If not specified - please check loop
and interface circuit, because assembly of this scheme no one
checked. Not recommended for use HDD over 40mb, because OS CP
/ M on the TURBO 2 + allows to break the screw only 7 parts.
Why seven? Because the disk monitor 10 channels: 1 - ramdisk
"A", 1 - Floppy "B", 1 - necessary for the proper functioning
of the copiers and formatter (MFLX, for example), there were 7
for your HDD. Why not less - file system CP / M rather Tupa, and
Search for entries in the directory spends
time is directly proportional to the size of the directory. For
example: running programs from 1Kb in size from one section of
the HDD capacity 4mb - 7 seconds! And download the kilobyte - a
few milliseconds, all the rest of the time consuming search the
directory. A scan of the same directory partition in XCOMANDERe
6 seconds! From the foregoing it follows that it is necessary
to make all sections different lengths (large - for trash and
toys, small - for useful software programs).
The recommended length of the sections:
C: 400 kbytes - for the most chastozapuskaemyh programs (trust
me, this is enough). D: 1 mbytes - for a seldom-used programs.
E:-I: Ostavsheecya space equally divided between the two discs.
Enter your chosen size disks
in the appropriate column of the program and
save it on the HDD (and just in case
- On a floppy disk). Next, restart
computer and make sure you have the system CP / M disks
desired. With utility FORMAT format all disks, (Those that are
in the drive, you can not format:)).
Everything that is written below it makes sense to do if you
have 1024K of RAM!
To correct mistakes you need to
have a programmer that is connected to IBM
or to SPECTRUM. Read the ROM and save it in a file. Next,
perform all necessary changes and put the other firmware.
Failed to work with the RAM-DISK 1024k.
When you install the 1024K memory arises
the following problem: during a CP / M for
copying the information in the RAM-DISK after
overflow first 416kb disk computer hangs tight, but when you
run the OSes, he honestly says: 1024 kbytes memory.
HoneyComander works perfectly normal. The error is
Playing a cross-transfer, which was simply transferred to the
authors with ATM-1 (where 1024K, did not exist).
To address this need in Gluck
ROM (with address # C000 to # FFFF) to find the combination of
byte # 6F, # C8, # CB, # 7C, # 3E, # 03 (in version 7.40 is the
address of # D1EC) and replace the code on # 6F # 7F. Work in
the CP / M with electronic drive is normal.
However, after such a change usually computer draws a
beautiful colored label: "I cracked, I halted, press reset to
continue ", as the ROM BIOS is protected from changes. To
remove this protection in ROM at address # C000 to # FFFF (CP /
M bios) Find a combination of # 01, # FF, # 3F,
# AF, # 67, # 6F, # 86 (in version 7.40 is
Address # C5BA) and replace the # 01 to # C9, then must find a
combination of # 21, # 00, # C0, # AF, # 86, # CE, # 00, # 23
(in Version 7.40 is the address of # C1C7) and replace
# 21 for # C9. You'll never see any
colored labels + you get a
the ability to edit TR-DOS.
