MS 6313

Greetings, All! Tell me, please, a description of the switches on the subject printer. All the best. David Willis.

Greetings, Roman! 24 Jul 00 00:10, Roman Chupak -> All: RC> Tell me, please, a description of the switches on the subject RC> printer. === Cut === ╔═══════════════════════════════ ═══════════════════════════════╗ ║ Printer "Electronics MC6313" version (LX800) FX800. ║ ║ GOST 21776-87. ║ ╚═══════════════════════════════ ═══════════════════════════════╝ Purpose of switches. ┌────────┬────────────────────── ──┬────────────────────────────┐ │Designation- │ Function │ Switch status │ │reading │ ├──────────────┬─────────────┤ │ │ │ 0 │ 1 │ ├────────┼────────────────────── ──┼──────────────┼─────────────┤ │ SA1.1 │ Paper end sensor │ Active │ Disabled │ │ │ │ │ │ │ SA1.2 │ Paper type │ Roll │ Sheets │ │ │ │ │ │ │ SA1.3 │ Rebate processing │ Skip │ No skip │ │ │ │ rebate │ ka rebate │ │ │ │ │ │ │ SA1.4 │ Zero image │ "0" │ "O" ││ │ │ │ │ │ SA1.5 │ Interface │ Joint C2 │ IRPR-M/IRPR │ │ │ │ (RS-232C) │ (CENTRONICS)│ │ │ │ │ │ │ SA1.6- │ Print density │ 00 - PIKA (80 characters/page)│ │ -SA1.7 │ │ 10 - ELITE (96 characters/page)│ │ │ │ 01 - Seal. PIKA (137) │ │ │ │ 11 - Seal. ELITE (160) │ │ │ │ │ │ │ SA1.8 │ Add. parameters inter- │ If Joint C2:│ If Joint C2:│ │ │ faces selected by SA1.5│ protocol │ protocol │ │ │ │ XON/XOFF; │ DTR; │ │ │ │ if IRPR-M: │ if IRPR-M:│ │ │ │ direct code │ inverse code│ │ │ │ │ │ │ SA2.1- │ Exchange speed by │ 000 - 75 100 - 1200 │ │ -SA2.3 │ Styku-S2, baud │ 001 - 150 101 - 2400 │ │ │ │ 010 - 300 110 - 4800 │ │ │ │ 011 - 600 111 - 9600 │ │ │ │ │ │ │ SA2.4- │ Parity │ 00 - no parity ││ -SA2.5 │ (parity) according to Joint-C2 │ 01 - without control │ │ │ │ 10 - odd parity│ │ │ │ 11 - parity check │ │ │ │ │ │ │ SA2.6- │ International selection │ 000 - Spain 100 - Italy│ │ -SA2.8 │ characters │ 001 - England 101 - Germ. │ │ │ │ 010 - Sweden 110 - Denmark │ │ │ │ 011 - France 111 - USA │ │ │ │ │ │ │ SA3.1- │ Connection of the kit │ LX800 kits: │ │ -SA3.4 │ characters │ 11x1 - set 1 (Russian continuous)│ │ │ │ 01x1 - set 2 (italics) │ │ │ │ 10x1 - set 3 (graphics) │ │ │ “Our” set (ZX-Word)--> 00x1 - set 4 (MAIN!) │ │ │ │ │ │ │ │ │ Old Russian sets: │ │ │ │ 0100 - set 5 (KOI-7 H1) │ │ │ │ 1100 - set 6 (KOI-7 H0) │ │ │ │ 1000 - set 7 (combined) │ │ │ │ 0000 - set 8 (combined complete)│ │ │ │ xx10 - set 9 (ordered) ││ │ │ │ │ │ SA3.5 │ INIT signal │ Blocked │ Active │ │ │ │ │ │ │ SA3.6 │ SELECT_IN signal │ Valid │ Latched│ │ │ │ depending│ in position │ │ │ │ from input │ "active" │ │ │ │ signal │ │ │ │ │ │ │ │ SA3.7 │ AUTOFEEDXT signal │ Active-"- │ Fixed│ │ │ │ -"- │ -"- │ │ │ │ │ │ │ SA3.8 │ Acoustic signal │ Disabled │ Active │ └────────┴────────────────────── ──┴──────────────┴─────────────┘ Numbering of switch blocks and switch sliders - from left to right. States: 0 - for yourself, 1 - for yourself. Positions: 0 - off, 1 - on, x - don't care. Switch positions for working in ZX-Word and most other programs: 01101000 00000111 00011101. Purpose of contacts of the IRPR-M connector: Inputs: 3 - Data0 - data bus; connect according to the diagram 5 - Data1 7 - Data2 9 - Data3 11 - Data4 13 - Data5 15 - Data6 17 - Data7 - -"- 23 - /STROBE - “strobe”; indicates that there is athere is a true combination of 0 and 1; connect according to the diagram 27 - /INIT (RESET; disable) 29 - /SELECT_IN - device selection (fix in active state) standing corresponding switch) 30 - /AUTOFEEDXT - automatic line feed after return carriages; switch SA3.7 is set to 0 (valid), but the input leave “hanging in the air” (log. 1); will be disabled Outputs: 19 - /ERROR - error; not needed 21 - BUSY - “busy”; needed; connect according to the diagram 25 - /ACKNOLEDGE - confirmation of data reception; not needed Service: 2 - housing (not connected to the common wire); better connect even numbers from 4 to 28 - common wire - connect according to the diagram 1 - +5V output through a 3.3 KOhm resistor. On ZX-SPECTRUM: connect Data0...7, /STROBE, BUSY, common, earth; on the ZX-Lprint-III interface connect to the common wire /ENPR (Enable Printing) signal (preferably directly in the connector, so that when When removing the connector, the interface was blocked). On PC: In WINDOWS, enter "LX-800 in LPT1:"; will work absolutely everything. You only need to connect to ground directly on the connector (with side of the computer) "paper break" signal. === Cut === With the best - Wlodek. mailto: wlblack@chat.ru [ZX] [Golyanovo] [Radio "Retro" 72.92 MHz]