EGA

Greetings, Alexey! PE>>> People, tell me how to use a subject monitor for a scorpion PE>>> connect, only PE>>> simpler plz =). AP> I have it connected like this (though not to Scorpio): monitor connector 9 AP> pin 1-GND 3-R 4-G 5-B 8 and 9 - frame and line (can AP> vice versa), on pins 2,6,7 brightness for each RGB color AP>separately, I don’t remember in what order, and it doesn’t matter, I have these three AP> brightnesses are twisted together and go to the speck brightness. HO! There is one AP> an unpleasant glitch (or maybe it should be) - all colors with brightness turned on AP> look great, but if the colors are without brightness, it’s unpleasant to look at, that’s all AP> very dark, especially white - it is some kind of dirty gray color, and yellow AP> - more like brown and almost merges with red without brightness. In AP> In connection with this, I have a question for knowledgeable people - is this possible somehow AP> fix? Sorry, I don’t remember where I stole from: === Begin file: zx/vga .txt === ZX + CGA, EGA, VGA monitors. (C) MPR Hard╔═══╦═════════════════╦══════════════════╗ ║NM║ CGA monitor ║ EGA monitor ║ ╠═══╬═════════════════╬══════════════════╣ ║ 1 ║ GND ║ GND ║ ║ 2 ║ GND ║ RED INT ║ ║ 3 ║ RED ║ RED ║ ║ 4 ║ GREEN ║ GREEN ║ ║ 5 ║ BLUE ║ BLUE ║ ║ 6 ║ INTENSITY ║ INT / INT GREEN ║ ║ 7 ║ - ║ INT BLUE / VIDEO ║ ║ 8 ║ HORIZONTAL SYNC ║ HORIZONTAL SYNC ║ ║ 9 ║ VERTICAL SYNC ║ VERTICAL SYNC ║ ╚═══╩═════════════════╩══════════════════╝ ╔═══╦════════════════════════════════════╗ ║N/M║ VGA monitor ║ ╠═══╬═════════════╦════╦═════════════════╣ ║ 1 ║ RED ║ 9 ║ - ║ ║ 2 ║ GREEN ║ 10 ║ GND ║ ║ 3 ║ BLUE ║ 11 ║ GND ║ ║ 4 ║ - ║ 12 ║ - ║ ║ 5 ║ test ║ 13 ║ HORIZONTAL SYNC ║ ║ 6 ║ GND * ║ 14 ║ VERTICAL SYNC ║ ║ 7 ║ GND * ║ 15 ║ - ║ ║ 8 ║ GND * ║ ║ ║ ╚═══╩═════════════╩════╩═════════════════╝ RED-GREEN-BLUE - красный-зеленый-синий INTENSITY - INT - сигнал яркости HORIZONTAL SYNC - строчные импульсы VERTICAL SYNC - кадровые импульсы GND - земля (общий) С подключением сигналов GND * советую поэкспериментировать. Подача сигналов на 6 и 7 выводы разъема EGA-монитора зависит от того, имеет лиThis monitor can be switched to CGA mode. I advise you to take all signals directly but where do they come from (for example, for me, R, G, B and I - from KP11, and frames and lines - from TM2). If the screen is shifted left and right, and the under- adjusting the monitor does not help, invert Write lowercase pulses. It is better to pass personnel impulses through buffer, because on some monitor models they shrink strongly, and on some models All computers are tied to interrupts - mi. ZXNet 095/360 CPS1/to_mpr MPR Hard from CPS HG,1996 ************************************************* This note is dedicated to everyone who has Speccy has a CGA/EGA monitor and it has color commercial problem, i.e. 2 black and dark yellow ty like dark red. This problem is solvable, but not completely, since you will have 1 black (as needed) and 1 yellow (but yellow). Needed for revision mikrukha M533KP7 and capacitor approximately 0.1 mkf. ┌──────────┐ I(c)──┤1 ▀ 16├──Ucc I(c)──┤2 M/S 15├──I(c) I(c)──┤3 14├──I(c) Gnd──┤4 13├──Ucc I(m)──┤5 12├──I(c) ──O6 11├──B Gnd──O7 10├──R Gnd──┤8 9├──G └──────────┘ I(c) - Brightness signal from computer I(m) - Freshly formed brightness to the monitor Ucc - +5v Gnd - Earth R,G,B - TTL levels in parallel with the connector Place a capacitor between +5v and Gnd. Compu-MS/Scorpion Club ZXNet: 095/500.4=== End file: zx/vga .txt === They just forgot to specify about VGA monitors that they should be with TV scans... 2ALL: And for a TV cord, all the cores must be separate screen, or is it enough to have everything on one screen? PS. Personally, I _sincerely_ advise everyone to look for TV monitors from Commodore - no problems at all - one continuous rulez! (I’m sitting on this now - I’m head over heels happy;) Happy. Michael.

Hello, Pavel Evzovich. PE>> People, tell me how to connect a subject monitor to a scorpion PE>> just simpler plz =). MM> Connector pinout: 1 - GND MM> 2 - red MM> 3 - RED MM> 4 - GREEN MM> 5 - BLUE MM> 6 - green/intensity (brightness) MM> 7 - blue MM> 8 - H synh (horizontal synchronization) MM> 9 - V synh (vertical synchronization) MM> I don’t know where the signal on the board comes from (for Scorpio), but it’s needed MM> TTL levels, on its brightness 50%, and on the spectrum 75, as a result on the monitor MM> low brightness colors are too low :( MM> On my computer (ala Pentagon) it was enough to select 1,3,4,5,6 MM> contact, and everything showed until I made the turbo, then I had to MM> add 8 and 9... MM> PS: who knows how to set the brightness to 75% in eG?I completely forgot, there the black color of increased brightness looks gray, that sucks, so a tiny scheme to prevent this from happening: R ┌───┐ ─────────┤ 1 │ ┌───┐ ┌───┐ G │ o───────┤ o───┤ 1 │ ─────────┤ │ └───┘ │ o───┐ B └───┘ ┌─────────┤ │ │ ┌───┐ ───────────────────┘ └───┘ └─┤ 1 │ BRIGHT' BRIGHT ┌───┐ │ o───────── ─────────────────────────────┤ o─────┤ │ └───┘ └───┘ The meaning is when the black color (R, G and B are at 0) the brightness is also at 0 on the monitor you need to submit BRIGHT' instead of BRIGHT. Sincerely, Max Melnikov... aka HighLander... aka Uncle Maximka... .·∙.■▀■▄■...[ProDiGy]...[GirlS]...[MetaLlicA]...■▀■▄■.∙·. `∙..∙·---──·─//─..[UnrEAl TouRNameNt]..─/─·──---·∙..∙','317

Hello, All Folks, how to connect an EGA monetizer to the Spectrum?

Hello, 80xx 80x> People, how to connect an EGA monetizer to the Spectrum? I recommend using the search! This is a repeated "accordion". For example: http://zx.pk.ru/showthread.php?t=1773&highlight=EGA

Hello, CHRV Sorry for my stupid question, I'm a beginner in this matter. I was given 2 interesting devices: BYTE with a rubber keyboard and Slavutich Kyiv production, but no money. What about this good stuff?

Hello, 80xx 80x> Sorry for my stupid question, I'm a beginner in this business. I was given 2 80x> interesting devices: BYTE with a rubber keyboard and Slavutich Kyiv 80x> production, but no money. What about this good stuff? It depends on what the tasks are and what tools you have. You can look for diagrams (for example, ask Conan).

Hello, 80xx 80x> Tell me, is it suitable for the Spectrum "video monitor Electronics 80x> 32VTTS202". On the back panel it has the same connector as on mine 80x> SLAVUTICH Will do. It would just be a good idea to check the pinouts of the connectors. I remember on mine Synthese-M had to be re-soldered.

Hello, CHRV CHR> Start by studying the circuits; Byte's circuit seems to have already been run through here. There may be confusion with the names: (01) these are Belarusian clones, very famous and built into the case with light gray plastic keyboard. is a completely different clone, produced by the Dniester plant (Bendery), in black case, with rubber keyboard. His diagram has not yet been found. HO! Through the efforts of Vlad Semchenko (aka Spensor), the clone circuit was restored ["http://zx.pk.ru/showpost.php?p=38380&postcount=399"] (Sevastopol Electromechanical Plant). Judging by the photo of the BYTE board, it is a simplified version of , without SECAM and HF encoder modulator. Therefore, the circuit (and most likely the pinout of the connectors, with the exception of HF) and the connection of Ts are identical.

Hello, 80xx Tell me, is it suitable for the Spectrum "video monitor Electronics 32VTC202". On the back the panel has the same connector as on my SLAVUTICH

Hello, CHRV It’s interesting to deal with Spectrum-compatible machines, Spectrum seems to be simple the car has a lot of capabilities, so I’m interested in going deeper, otherwise I'm tired of ordinary pussies, they're kind of boring. I apologize in advance for the stupid ones questions, I'm a beginner :confused:

Hello, 80xx 80x> Interesting to deal with Spectrum-compatible machines, Spectrum 80x> it seems like a simple machine but it has wide capabilities, that’s what I want 80x> It’s interesting to dig deeper, otherwise I’m tired of ordinary pussies, they’re boring 80x> some. I apologize in advance for stupid questions, I'm a beginner 80x> :confused: Start by studying the circuits; Byte's circuit seems to have already been used here.

Hello Conan Thank you all very much for your help, I’ll look into it, this is a very interesting technique

Hello Conan Con> this is a completely different clone, produced by the plant ( Con> Bender), in a black case, with a rubber keyboard. His schemes are still Con> no results found. Con> Picture: http://www.homecomputer.de/images/wanted/easteurope/Byte_2.jpg Is this him? Photo taken from the link that flew here http://www.homecomputer.de/pages/easteurope_ussr.html. By the way, it should be there Capture photos for posterity. It’s a shame that we don’t have any of our own!

Hello Conan Dear Conan, I’ll try to take a photo of my device this evening and post it photo

Hello icebear ice> Is this him? Andreas, the photo above shows a computer with a regular keyboard. Judging by the description 80xx (and others), its "BYTE" has rubber. Possibly in the picture from German website third option "BYTE" (or just a homemade machine). P.S. A photo of "BYTE" (the one from the respected 80xx) would be very useful.

Hello, 80xx Dear Conan, I’m posting pictures as promised, one of these days I’ll take pictures of three machines. Tell me if you have a circuit diagram for the monitor "Electronics 32 VTC 202" or Tell me where I can get this circuit, I got the monitor and connect my own speck I can’t, they have different socket pinouts. Thanks in advance File: SLAVUTICH.JPG http://zx.pk.ru/attachment.php?attachmentid=2660 File: BYTE.JPG http://zx.pk.ru/attachment.php?attachmentid=2661

Hello, 80xx 80x> Dear Conan, I’m posting pictures as promised, I’ll take pictures one of these days 80x> escho three machines. Tell me if you have a circuit for the "Electronics" monitor 80x> 32 WTC 202" or tell me where I can get this diagram, or a monitor 80x> I got it, but I can’t connect my spec, they have a socket layout 80x> different. Thanks in advance Oh well, we don’t use search ;). Look here: http://zx.pk.ru/showthread.php?t=178

Hello, 80xx 80x> Dear Conan, I’m posting pictures as promised, I’ll take pictures one of these days 80x> three machines However, the Germans (see link above) also have such a photograph, but only this one the "normal" (in terms of size) version is not available. So OH! :)

Hello icebear 80x> I’m posting pictures as promised, one of these days I’ll take pictures of three cars. Is it possible to provide a photo of the "BYTE" board? It is also possible in low resolution.

Hello spensor Dear Spensor, at your request, I am posting a photo of the BYTE board File: BYTE.JPG http://zx.pk.ru/attachment.php?attachmentid=2716

Hello, 80xx 2Spensor: On that German site it is said that “Sail” displays a splash screen - "Didaktik Skalica". Is that so?

Hello Conan Con> or just a homemade machine It doesn’t look like a home-made one. In the corners of the body, shrinkage is clearly visible in the places of the posts for fastening housing halves.

Hello icebear ice> Is this him? Hmm, I wonder what kind of BYTE variant this is?

Hello Costa ice> However, the Germans (see link above) also have such a photograph, but here ice> only its "normal" (in terms of size) version is not available. So ice> OH! It turned out that BYTE has a regular keyboard made in Moldova, and the one that with rubber Ts Ukrainian. Cos> Doesn't look like a home-made one. In the corners of the body, shrinkage is clearly visible in places Cos> posts for fastening the body halves. It’s just the case and keyboard that look homemade. Similar constructs (with poorly stamped) were sold on radio markets. But a photograph was discovered (poor quality), where such a BYTE is shown complete with typographical instructions and a factory power supply (the size of a computer). What can you use? draw a preliminary conclusion that this is the variant of the same name. Shed light on it the origin could be a photograph of the board.