RDC

Hi, Oleg! I tried the subject... Well, well... There are such autoconfig procedures for memory: that just shoot yourself... Why didn't he go... Error in the code. There's a wild procedure that checks (as far as I understand) memory card. Does She did this by sorting through 128 cans. In short, the command at #7C3F should look like LD HL,#BD7F, not #BD7E. It worked. I must say, quite fast copier hehe... But the interface could have been more convenient do... And if I ate and isdos/msdos wheels, that would be great! And also - why is this a bunch of ram disks? For some reason they are not available to me... Obviously, for a Sprinter with 4 meters :) And so - only for Profei. And there are very few Profei. Or under megabyte Kai. But just then he appeared... And turn off the engine after the start. He selects disk "d", which is not there, and the motor will spin forever... P.S. It malfunctioned once... It sucked in disk "b" for the purpose of copy to "a", and suddenly switched to "c". I pressed the break - instead of a fountain there was porridge. And froze. Best wishes. Dmitry aka -=LD=- / X-TRADE GROUP. -+- ZXASM 3.0

Hello, Dmitry! 02/28/98 at 03:04 Dmitry Lomov wrote to Oleg Grigoryev on theme "RDC". DL> There are such autoconfig procedures for memory DL> why just shoot yourself... Not my idea. I just screwed up Pashino a little. ;) DL> It worked. Looks like you erased it? ;))) DL> I must say, enough DL> fast copier. Theoretically it can be even faster. For example, when going to another track to read the address and start reading sectors from next. I'll have to check it out. DL> hehe... But the interface could have been more convenient DL> do... What's not to like? Such a smart guy. Not an arrow of course but IMHO the cursor is faster than the arrow. Even faster hotkeys. DL> And if you ate isdos/msdos DL> disks, that would be great! It's easy in principle. isdos 800kb and msdos 720 kb. Me in the fall dissuaded. Only with the output of the directory will you have to break off. Well The root one is still possible, but what about the rest? Yes, and you need memory for this. I'll make a copy. And I’m still not sure about the need to stuff transferring these disks into memory. see below. It is unlikely that anyone will come to I'd like to replicate MSDOs disks on a spec, although this is the case with ISDOS maybe I'll think about it. DL> And also - why this DL> a bunch of ram disks? For some reason they are not available to me... What do you mean it says impossible? It will be necessary to re- redo. You used then turn it on, but for all mode you need a buffer like minimum for 41 jars. 40 will go to disk, and one will be used as a buffer for copying will remain. By the way, it’s cool to copy from the dis- to a disk with a 16 kilo buffer;))) DL> Obviously, for a Sprinter with 4 meters :) But no;) I can’t even imagine how memory goes there - Xia. But these are the problems of sprinters. It’s necessary - let them write it themselves, otherwise Apart from advertising, no information. Initially intended for gmx two-meter long, it fits just 3 full disks. A 4 de- lano based on used. Yes, when reading in used prog mode relies on information from sector 8, but how else?.. DL> And so - only for Profei. And there are very few Profei. At one time, the spectrophone was intensely frightened by huge crowds - these same ones...;))) DL> Or under megabyte Kai. But just like that, he appeared... !!! Nemo is still alive! ;))) DL> And turn off the engine after start. I did. Like the version that you just threw? Setup refused I got busy and became lazy. And I wanted to push the drive settings, i.e. all sorts of delays. And yet, by chance you don’t know howSo can you read 3-inch disks at a speed of 5-inch? A then they usually slow down. I used to think that this was alright cabbage soup, but Black Raven convinced me otherwise. DL> P.S. It malfunctioned once... It sucked in disk "b" with a purpose DL> copy to "a", and suddenly switched to "c". I hate such bugs! Which pop up once a week. And in more details? Precisely while reading? or during the switching process nia? or something else? I'll have to check/rewrite everything, I'll I wanted to do it, but I got lazy. I have a terrible mess there now, especially at the start of copying. Best wishes, Oleg aka Ruiner. -+- Shoot-Edit v6.06

Hi, Oleg! DL>> It worked. OG> You seem to have erased it?;))) So it's new and working... DL>> I must say, quite DL>> fast copier. OG> Theoretically, it can be even faster. For example, when going to OG> read the address for another track and start reading sectors OG> from next. I'll have to check it out. That's the only way! DL>> hehe... And the interface could have been more convenient DL>> do... OG> What's not to like? Such a smart guy. Not an arrow, of course OG> but IMHO the cursor is faster than the arrow. Hotkeys are even faster. Well. for example... It writes impossibly, you press a key, and it moves to the main menu... Not enough information on the screen. It would be possible write that such and such disks are empty, such and such are impossible, and there are no such things at all... DL>> Or under megabyte Kai. But just like that, he appeared... OG> !!! Nemo is still alive!;))) There is a little... Just a little. No matter how hard I tried to persuade him to make a Pentagon temporary hut in a new car - he’s in no way... But there are also positive features in the new Kai. Wait is removed therein non-turbo mode... Making a normal temporary hut has become easier... DL>> And turn off the motor after start. OG> i.e. all sorts of delays. And yet, by chance you don’t know how OG> so you can read 3-inch disks at a speed of 5-inch? A OG> then they usually slow down. I used to think that this was alright OG> cabbage soup, but Black Raven convinced me otherwise. They walk slowly. When formatting you need to do inter-track displacement is not one, but two sectors. Interlateral The offset can always be set to zero. If you need to read a disk of an unknown format, The option to catch the address after the step is suitable. Or program the following reading sequence (fast format, shift in sectors is done on each track, including crossing to the other side, like ADS): Track 0/0: 0,1,2...14,15 Track 0/1: 0,1,2...14,15 track 1/0: 1,2,3...14,15,0 track 1/1: 0,1,2...14,15 Immediately after the step, sector 1 is caught, not 0. 0 is caught at the end. Then you suddenly change sides and manage to get right to zero. OG> I hate such bugs! Which pop up once a week. And in OG> more details? Precisely while reading? or in the process of switching But I don’t remember... I think I didn’t finish reading... All the best.Dmitry aka -=LD=- / X-TRADE GROUP. -+- SMM version 1.08