HDRIVER_.hrp

Hello, All! Subject for testing (for SMUC-com1). Setup recommendations: The driver at offset + #3A contains all commands sent to the modem You must adjust some commands to suit your modem. First comes the team name ending with a colon, then the command ending with the code #0D or symbols replacing #0D= (!) or (|) and in at the very end there should be a line ending code #00 example - INIT:ATZ!#00 The order of the commands is as follows: ───────────────┬─── ─────────────┬────── ──────────────────── ──────────────────── ─ command │ number of bytes │ comment │ allocated │ │ under command │ ───────────────┼─── ─────────────┼────── ──────────────────── ──────────────────── ─ INIT: │ DS 40 │ modem initialization line HANGUP: │ DS 15 │ disconnect (DISCONNECT) BUSY: │ DS 10 │ interrupt execution of commands ATX3D/ATA/ATDP/ATDT DIALP: │ DS 15 │ dial number (pulse dialing) DIALT: │ DS 15 │ dial number (tone dialing) ANSWER: │ DS 20 │ active connection (ATA) DATA: │ DS 20 │ passive connection (ATX3D) BAUD: │ DS 1 │ port speed (0-2400 to 6-115200) │ │───────────────┴─── ─────────────┴────── ──────────────────── ──────────────────── ─ Now point by point: ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ INIT - called during initial driver installation and after commands BUSY, HANGUP For the driver to work properly, the modem must be installed correctly configured therefore care should be taken to contents of the initialization string, after initialization it should ensure that the modem operates in hardware control mode stream RTS/CTS, in order to avoid misunderstandings, I present my configuration, with these settings everything is ok for me. ati4 USRobotics Sportster 14400 Fax Settings... B0 E1 F1 L0 M3 Q0 V1 X4 Y0 BAUD=19200 PARITY=N WORDLEN=8 DIAL=HUNT ON HOOK &A3 &B1 &C1 &D2 &G0 &H1 &I0 &K3 &M5 &N0 &P0 &R2 &S0 &T5 &Y1 S00=000 S01=000 S02=043 S03=013 S04=010 S05=008 S06=002 S07=060 S08=002 S09=006 S10=014 S11=070 S12=050 S13=000 S15=000 S16=000 S18=000 S19=000 S21=010 S22=017 S23=019 S25=005 S27=000 S28=008 S29=020 S36=014 S38=000 LAST DIALED #: OK ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ HANGUP - called to break a connection, usually the contents of this line are:!v~~^`!!`` or you can do this ~+++~ATH0! specialist. symbols in commands: ! - replaced by #0D | - replaced by #0D ~ - pause of 50 interruptions ` - pause of 5 interruptions v - reset DTR ^ - set DTR ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ BUSY - called to interrupt the action of ATX3D/ATA/ATDP/ATDT commands, Usually, to interrupt the action of these commands, it is enough to send to the modem code #0D (or any character at all) ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ DIALP - called to pulse dial a number, usually the contents of this line ATDP, WARNING AT THE END OF THIS COMMAND THE CODE #OD OR A SUBSTITUTE FOR IT IT IS NOT NECESSARY, THIS IS DONE IN THE RECRUITMENT SUBROUTINE ITSELF. ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ DIALT - called for tone dialing, usually the contents of this line ATDT, WARNING AT THE END OF THIS COMMAND CODE #0D OR ITS SUBSTITUTE IT IS NOT NECESSARY, THIS IS DONE IN THE RECRUITMENT SUBROUTINE ITSELF. ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ ANSWER - called to attempt an active connection, usually the contents of this ATA strings.─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ DATA - called to attempt a passive connection, usually the contents of this ATX3D strings. ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ BAUD - port speed from #00-2400 to #06-115200, WARNING is not an ASCII character. ─────────────────── ──────────────────── ──────────────────── ──────────────────── ─ More nuances, in MMD2.20 itself you need to set the SPEED SETTING flag otherwise the active and passive connection commands will not work. The entire description is over, if you forgot anything, please clear it, as it’s a test version Please, if there are any glitches, if you have any wishes or misunderstandings of anything in the settings, soap to the addresses: FidoNet 2:5030/675.32 ZxNet 500:812/1.32 Alexandr Tkachev Alexandr.

Здравствуй, All ! А вот тут файл HDRIVER_.hrp section 1 of 1 of file HDRIVER_.hrp < Lara Croft 4.50 UUE > begin 644 HDRIVER_.hrp M2%)I`:T$``%(L^K5-715*CZC^ELM57 M.Q8,[]$;.IE0D%51#H$V")?PNLAV,$!*`#ML``!NO^=UTQ`'^?LULQ.8/ MQ+_[PGC!^^L&?*_I!*MVZKO[!GB]^GL^@$'I8`EY(9[!.NK`AU6`!G'[(% M(RKAZ&WA`^[X!:^[^NU>>T7]+X/LDR^,"9[5N`S2&L@2Q^@M>65S(&UO9!"!"7+!:780'&9OQ_Q-B40RC2XP#U--PU5#7>HN#3^/6453?SOI M/!C_R?/_-P[^.NO"MR#<$0;_]@0]!4@X_8!`GDWR/CN_JH@[3_9PSCK_NU5(.3M]^)?_/K<5^U3<)81G__S MSWX"1,#*! M7[-UF^@^?Q-_V_#^'S_00VSY[U594!Y2%V#NJO7UPR_K7O>GO*E_"ST$0 M*/=L5P@@$N]@UUYWA>/)_D^`/8H1WERK0$R$UZU_K/^T"BCG=R,+#2#/X3K=/+THG]K'7UKTL&>-SZ.+4% M__?MP=$_R<6]]6X*$"CYU].G!-*:-OQ?]+!R7ZWDB9_0W$V$_B(2@B1'SD M'@8RTB@<4`6A8'$6UG8`$^@@S1,OGROHQCBT#X->`;-41Z]'EPI@:[@84 M^W80_?/)]<4^`1@$WOH#?];!